Piping Hardware

MS vs HDG vs SS Flanges: Choosing the Right Pipe Flange

Put three DN100 flanges side by side on a workbench. One is mild steel, one is hot-dip galvanised and one is stainless. Same bore, same bolt circle, same number of holes. Install them on the same project and one might still look new in fifteen years, one might need repainting every monsoon, and one might be leaking at a rusted bolt hole before the warranty runs out.

The flange that fails isn’t badly made. It was simply put in the wrong environment.

That is the real story behind MS vs HDG vs SS flanges. None of the three is “best”. Each one is the right answer for a particular combination of fluid, temperature, exposure and budget.

So how do you tell which one your line needs? Start with what each option actually is and where each one belongs. Then check the pressure-rating detail that catches many buyers out, and write an enquiry that gets you the right flange the first time. The sections below take those steps in order.

The Short Answer

If your line is…The usual choiceBecause
Indoors, dry or painted, at moderate or high temperatureMS (carbon steel) flangeLowest cost, easy to weld, full pressure ratings
Outdoors or damp, carrying water or utilities, below about 200 °CHDG flangeZinc gives long, low-maintenance protection at modest cost
Exposed to chlorides, chemicals, hygiene rules or wash-downSS flange (304 or 316)The corrosion resistance comes from the alloy itself

Everything below explains the exceptions, and there are more of those than most catalogues admit.

First, Fix the Terminology: Two Materials and One Finish

The labels MS, HDG and SS look like three equal options. They aren’t quite.

  • MS (mild steel) is a base material: low-carbon steel. In flange terms that usually means plate flanges cut from IS 2062 structural steel, or forged carbon steel flanges to ASTM A105 for pressure piping.
  • SS (stainless steel) is also a base material: an iron alloy with enough chromium to form a self-healing protective film. Flanges are typically 304/304L or 316/316L, forged to ASTM A182 or cut from stainless plate.
  • HDG (hot-dip galvanised) is a finish, not a metal of its own. An HDG flange is a carbon steel flange dipped in molten zinc. Its strength and pressure rating come from the steel underneath. Its corrosion resistance comes from the zinc on top.

This is why the specification on our MS / HDG / SS flanges page asks for the base material grade as well as the finish. “HDG flange” tells a supplier how the flange is protected, not what it is made of.

In Indian trade, “GI flange” usually means the same thing as HDG. Confirm it is hot-dip galvanised, though, not thinly electro-galvanised. Our explainer on MS vs GI covers that coating difference in detail.

MS Flanges: The Economical Workhorse

Mild steel flanges are the default on a huge share of Indian projects, and for good reason. They are the cheapest of the three, easy to weld, easy to machine and available in every common type: slip-on, weld neck, blind, threaded, socket weld, lap joint and plate.

Bare mild steel, however, has no corrosion resistance of its own. Moisture, humidity and condensation will rust it, so an MS flange always depends on something else for protection. Usually that’s primer and paint, sometimes an epoxy or wrapping system, and occasionally just the fact that it lives in a dry plant room.

Where MS flanges make sense:

  • Fire-fighting mains and hydrant headers in pump rooms and inside buildings, painted to the project colour code
  • HVAC chilled-water and condenser-water pipework in closed, treated loops
  • Steam, thermic fluid and hydrocarbon lines, where carbon steel to the relevant code is normally specified anyway
  • Compressed air and general utility lines indoors

Where they struggle: outdoor exposure without a maintained paint system, buried service without proper coating, splash zones, and anywhere condensation sits on the flange for months. A painted MS flange outdoors is only as good as the next repaint.

HDG Flanges: Steel Underneath, Zinc on Top

Hot-dip galvanising coats the whole flange, inside the bolt holes and across the faces, with a metallurgically bonded zinc layer. Zinc protects steel twice over. It acts as a barrier, and where the coating is scratched it corrodes sacrificially in place of the steel.

For thicker steel sections, which includes most flanges, ISO 1461 asks for a mean coating of at least 85 microns (about 610 g/m²) for steel over 6 mm thick, with no local reading below 70 microns. That is far heavier than electro-galvanising, and it is why an HDG flange can sit outdoors for many years with little maintenance.

Four things to know before you specify HDG

1. Galvanise after fabrication, not before. If a flange is to be welded to a pipe or spool, the ideal sequence is to fabricate first and galvanise the finished assembly. Welding a galvanised flange on site burns off the zinc near the weld. It also produces zinc oxide fumes, which can cause metal fume fever in poorly ventilated spaces.

If site welding can’t be avoided, remove the coating for roughly 25 mm either side of the weld and use proper extraction. Then restore the area with zinc-rich paint applied to a thickness of at least 100 microns.

2. Respect the temperature limit. Industry guidance from the American Galvanizers Association is to keep continuous service below about 200 °C. Between roughly 200 and 250 °C the outer zinc layer may begin to peel, and above that, deterioration speeds up. HDG flanges therefore have no place on steam or thermic fluid lines.

3. Watch hot-water circuits. In water between about 60 and 82 °C, if it contains dissolved oxygen plus bicarbonate or nitrate ions, zinc can reverse polarity. The steel then becomes the sacrificial metal. This only happens under that specific combination of conditions, but it is why galvanised flanges are a riskier choice for some hot-water circuits than the 200 °C limit suggests.

4. Mind the threads and faces. Female threads on threaded HDG flanges need cleaning or re-chasing after galvanising so the pipe makes up properly. Zinc runs or lumps on a raised face should be dressed smooth, or the gasket won’t seat evenly.

Where HDG flanges make sense: potable and domestic water on GI pipework, cooling-tower and outdoor utility lines, irrigation and pumping stations, and outdoor structural or support flanges. In short, the wet-but-not-hot jobs.

SS Flanges: When Corrosion Resistance Comes from the Alloy

Stainless steel needs no coating at all. Its chromium content forms a thin passive film that repairs itself when scratched, as long as oxygen is present. That makes SS flanges the natural choice where coatings would be damaged, contaminated or impossible to maintain.

304 vs 316: the molybdenum question

  • 304 (and 304L) is the general-purpose grade. It performs well for inland atmospheres, clean water, food processing and many mild chemicals.
  • 316 (and 316L) adds about 2–3% molybdenum, which greatly improves resistance to chlorides. That matters for coastal sites, effluent, brine, chlorinated water and many process chemicals.

Chlorides are 304’s weak point. In chloride-rich water or salt-laden air, 304 can suffer pitting and crevice corrosion. These are small, deep attacks that start exactly where flanges have tight gaps: under gaskets and around bolt holes.

Why the “L” matters

The L grades (304L, 316L) limit carbon to 0.03% maximum. Lower carbon reduces the risk of intergranular corrosion in the heat-affected zone after welding, which is why L grades are the usual choice for welded stainless systems. As you’ll see in the next section, it also lowers the pressure rating.

Where SS flanges make sense: food, dairy, beverage and pharmaceutical plants, coastal and port installations, STP and ETP lines, chemical dosing, desalination and RO plants, and wash-down areas. The trade-off is cost, since stainless flanges typically cost several times as much as an MS flange of the same size.

The Pressure Rating Surprise: “Class 150” Isn’t One Number

Here is the detail that most comparisons skip. Flange classes such as ASME Class 150 or EN PN16 are pressure designations, not fixed pressure values. The pressure a flange is actually allowed to carry depends on its material and its operating temperature.

Under ASME B16.5, a Class 150 flange is rated as follows:

Material (B16.5 group)Rating at −29 to 38 °CRating at 200 °C
Carbon steel, ASTM A105 (Group 1.1)19.6 bar13.8 bar
Stainless 304 or 316 (Groups 2.1 / 2.2)19.0 barLower than at ambient. Check the B16.5 table for your exact temperature
Stainless 304L or 316L (Group 2.3)15.9 bar11.2 bar

Two practical lessons follow:

  1. Switching from carbon steel to 316L at the same class can remove almost a fifth of your allowable pressure at ambient temperature. If the line runs close to its rating, the designer may need to step up a class.
  2. An HDG flange carries the rating of its base steel, but its zinc coating limits it to below about 200 °C. The coating limit, not the pressure table, usually decides where HDG can go.

EN 1092-1 PN ratings follow the same logic, with allowable pressure varying by material group and temperature. Always check the rating table for the actual material, not just the class stamped on the rim.

MS vs HDG vs SS Flanges: Side-by-Side

FactorMS flangeHDG flangeSS flange
What it isCarbon steel, usually paintedCarbon steel with a thick zinc coatingStainless alloy, 304/304L or 316/316L
Corrosion resistancePoor unless coated and maintainedGood outdoors and in water; zinc is consumed over timeVery good; 316 needed for chlorides
Temperature limit (corrosion protection)Set by the paint systemAbout 200 °C continuousHigh; set by the grade and code
Pressure rating basisBase steel (for example A105, Group 1.1)Same as its base steelStainless groups; L grades rate lower
Weldability on siteExcellentPossible, but coating must be removed and repairedGood, with correct procedure and L grades
MaintenancePeriodic repaintingLowVery low
Relative costLowestModerate premium over MSHighest, often several times MS
Matching boltingMS or HT bolts, coated to suitHDG bolts, nuts and washersStainless bolting with anti-seize

Which Flange for Which Line? An Application Map for Indian Projects

ApplicationUsual choiceWatch out for
Fire hydrant and sprinkler mainsMS, painted; HDG where the specification asks for itBuried sections need wrapping or coating; always follow the fire consultant’s specification
Potable and domestic water on GI pipeHDG, threaded or slip-onHot-water circuits in the 60–82 °C band
HVAC chilled and condenser waterMS, primed and painted under insulationCondensation under failed insulation on chilled lines
Cooling towers and outdoor utilitiesHDG, or SS 304Water chemistry; chloride levels decide whether 304 is enough
STP, ETP and effluentSS 316/316L, or HDG for mild duty304 can pit in chloride-rich effluent
Food, dairy, beverage and pharmaSS 304 or 316LUse L grades for welded systems and hygienic gaskets
Coastal sites, ports and desalinationSS 316/316L, or HDG with a maintenance planCrevice corrosion under gaskets in seawater service
Chemical and fertiliser plantsSS 316L, or a thermoplastic or lined systemCheck corrosion data for the exact chemical and temperature
Steam, thermic fluid and hydrocarbonsCarbon steel to the applicable codeNever HDG above about 200 °C
Compressed air and general utilitiesMS or HDGCondensate in wet-air systems rusts MS from inside

For thermoplastic pipelines such as HDPE effluent or water lines, the flange question changes completely. There, a backing ring with a protective polymer coating is often the better answer, explained in our guide to what a PP-coated steel flange is and why you’d use one.

Flange Type Matters Too: Threaded, Lap Joint, Weld Neck and Blind

Material and flange type are separate choices, and the right pairing can save money or trouble.

  • Threaded flanges screw onto threaded pipe with no welding at all. That makes them a natural partner for galvanised water lines, because no heat ever touches the zinc. They suit low-pressure, low-vibration services and are common on GI pipework.
  • Lap joint (loose) flanges sit behind a stub end that is welded or formed on the pipe. Only the stub end touches the fluid, so the loose flange can be a cheaper material. On an indoor stainless line, for example, a coated carbon steel backing flange over a stainless stub end can cut cost noticeably. Loose flanges also rotate, which makes bolt-hole alignment easy.
  • Weld neck flanges have a tapered hub that is butt-welded to the pipe. They are the choice for high pressure, high temperature and cyclic loading, in any material.
  • Slip-on and plate flanges are cheaper and easier to align. They are widely used on low- and medium-pressure utility, fire and water lines.
  • Blind flanges close off test points and future connections. On outdoor lines, an HDG or stainless blind avoids the rust stain that a bare MS blind leaves behind.

The backing-flange idea is taken a step further on thermoplastic pipelines, where the loose flange is often a steel ring sealed inside a polymer coating.

Bolts, Nuts and Gaskets Must Match the Flange

A flange is only one part of a flanged joint. The bolting and gasket have to suit the same environment, or the weakest part decides the service life.

Gasket material must suit the fluid, temperature and flange face. Our comparison of neoprene gaskets vs rubber gaskets is a good place to start for water and utility services.

Tightening matters just as much. A flange tightened bolt-by-bolt around the circle instead of in a star pattern can leak with perfect parts. Our article on torque specifications explains why.

Mixing Metals at a Flanged Joint

Sooner or later, a stainless flange has to meet a carbon steel or galvanised one, for example at a pump, a valve or a tie-in to existing pipework. In a dry location this is rarely a problem. In wet, conductive conditions, the zinc or carbon steel side becomes the anode and corrodes faster, while the stainless side is protected.

Where the risk is real, the standard fix is a flange isolation (insulation) kit. It consists of:

  • an insulating gasket, typically a glass-reinforced laminate or neoprene-faced phenolic
  • insulating sleeves around each bolt
  • insulating washers under the nuts
  • steel backing washers so the insulating washers aren’t crushed

Isolation kits are also used where a cathodically protected buried pipeline meets above-ground plant piping. For the electrochemistry behind this, read why you shouldn’t mix dissimilar metal fasteners. If your site is near the sea or a chemical plant, our article on preventing fastener corrosion in coastal and industrial environments covers the wider picture.

Seven Flange Specification Mistakes That Cost Money

  1. Ordering by material name alone. “SS flange, 4 inch, 20 nos.” leaves the type, standard, class, face and grade to guesswork.
  2. Putting HDG on a hot line. Above about 200 °C the zinc degrades, and some hot-water circuits are risky well below that.
  3. Welding galvanised flanges on site with no repair plan. The weld zone loses its protection, and the fumes need controlling.
  4. Choosing 304 for chloride service. Coastal air, effluent and brine call for 316/316L at minimum.
  5. Assuming the same class means the same pressure. L-grade stainless rates noticeably lower than carbon steel at the same class.
  6. Mating a raised-face flange to a flat-face cast iron or plastic flange. The raised face acts as a pivot and can crack the weaker flange. Use flat-face flanges with a full-face gasket instead.
  7. Mismatching the drilling standard. BS 10 Table D or E, IS 6392, EN 1092-1 and ASME B16.5 drillings are not interchangeable across the board. Check the bolt circle and hole count against the equipment you’re connecting to.

How to Write a Flange Enquiry That Gets an Accurate Quote

The quickest way to a correct quotation is one complete line per item. Include the flange type, nominal size, bore or pipe schedule, rating or PN, facing, material grade, standard, quantity and delivery city.

Two examples:

  • Slip-on plate flange, DN100, bored to suit 114.3 mm OD pipe, IS 6392 PN16 drilling, flat face, IS 2062 steel, hot-dip galvanised to ISO 1461: 40 nos., delivery Pune.
  • Weld neck flange, NPS 4, Sch 40 bore, ASME B16.5 Class 150, raised face, ASTM A182 F316L: 12 nos., EN 10204 3.1 certificates, delivery Chennai.

If you need certificates, coating-thickness reports, dimensional records or third-party inspection, say so at the enquiry stage. Requirements added after manufacture are hard to reconstruct. Our guides on fastener traceability and lot numbers and building an RFQ that suppliers can price quickly explain what to ask for and why.

Frequently Asked Questions

Which is better: an MS, HDG or SS flange?

None of them is better in every case. MS is the economical choice for dry, painted or high-temperature service, HDG suits outdoor and water services below about 200 °C, and SS is the choice for chlorides, chemicals and hygiene-critical plants. The right flange depends on the fluid, temperature, exposure, applicable code and how long it must last.

Is a GI flange the same as an HDG flange?

In Indian trade usage, “GI flange” usually means a hot-dip galvanised flange. It is still worth confirming the process, because electro-galvanised parts carry a much thinner zinc layer and won’t last as long outdoors.

Can HDG flanges be welded?

They can, but it isn’t ideal. The best practice is to weld first and galvanise the finished assembly. If welding after galvanising is unavoidable, remove the zinc for about 25 mm either side of the weld, ventilate or extract the fumes, and restore the area with zinc-rich paint to at least 100 microns.

What is the maximum temperature for galvanised flanges?

Industry guidance is to keep continuous service below about 200 °C, since the zinc can start to peel above that. Some hot-water circuits between about 60 and 82 °C can also be a problem, depending on the water chemistry.

Should I choose SS 304 or SS 316 flanges?

Choose 304 for general inland service, clean water and many food applications. Choose 316 or 316L wherever chlorides are present, such as coastal air, effluent, brine and chlorinated water, or for many process chemicals. Use the L grades for welded systems.

Can I bolt a stainless steel flange to an MS or HDG flange?

Mechanically, yes. In wet or conductive conditions, though, the carbon steel or zinc side will corrode faster through galvanic action. Where that risk is significant, use a flange isolation kit with an insulating gasket, sleeves and washers.

Do stainless steel flanges need stainless steel bolts?

In most cases, yes. Carbon steel or zinc-plated bolts in a stainless flange corrode quickly because they become the sacrificial metal. Use stainless bolting with anti-seize to prevent galling, or higher-strength alloy studs where the pressure class demands them.

Conclusion

A flange is a twenty-year decision that usually gets made in a day. The fastest way to settle MS vs HDG vs SS flanges is to start with the environment, not the price list. Ask what the flange will live in, how hot it will get and what it will touch.

Then pick the material and finish that survive those conditions. Check the pressure rating for that material, and order matching bolts and gaskets with it.

We supply MS, HDG and stainless flanges, with matching bolting, to projects across India, from Delhi NCR to Mumbai and Gujarat. Send your enquiry line through our contact page, or start from the MS / HDG / SS flanges product page. We’ll confirm the specification in writing before anything is made.

2 thoughts on “MS vs HDG vs SS Flanges: Choosing the Right Pipe Flange”

Leave a Reply

Your email address will not be published. Required fields are marked *