Bolt Grades Explained: What Do 4.6, 8.8, 10.9 and 12.9 Mean?
Two numbers and a dot. That is usually all the head of a metric bolt tells you, yet those few characters carry more engineering information than anything else on the part. Read “8.8” correctly and you know the bolt’s breaking strength, the point at which it starts to stretch for good, roughly how hard it is, which nut it needs and how it should be tightened.
Misread it and the mistakes cost money in both directions. Under-specify and a joint loosens, stretches or snaps. Over-specify and you pay for strength the joint can’t use, or you fit a brittle bolt where a tougher one would have lasted longer.
Here is what each of the four common bolt grades, 4.6, 8.8, 10.9 and 12.9, actually guarantees. We’ll turn the numbers into kilonewtons for everyday sizes, show how to identify a grade on site, and match each one to the right nut, washer and coating. The last sections cover how to choose a grade and how to write it on a purchase order.
Quick answer: A metric bolt grade, formally its property class, is two numbers. The first number multiplied by 100 gives the nominal tensile strength in MPa (N/mm²). The second number divided by 10 gives the ratio of yield strength to tensile strength. So 4.6 means about 400 MPa tensile and 240 MPa yield, 8.8 means 800 and 640, 10.9 means 1,000 and 900, and 12.9 means 1,200 and 1,080. Higher grades carry more load, but they are less ductile, need stronger nuts and harder washers, and are more sensitive to hydrogen embrittlement from some coatings.
Decode Any Bolt Grade in Ten Seconds
The property class system comes from ISO 898-1, which India adopts word for word as IS 1367 (Part 3). It packs two facts into one short code.
The first number gives the nominal tensile strength. Multiply it by 100 to get MPa. Tensile strength is the stress at which the bolt breaks.
The second number gives the yield ratio. Divide it by 10. Multiply the first number by the second and then by 10, and you get the nominal yield strength: the stress at which the bolt stops springing back and starts to stretch permanently.
| Grade | First number × 100 = tensile | Second number ÷ 10 = yield ratio | Nominal yield |
|---|---|---|---|
| 4.6 | 400 MPa | 0.6 | 400 × 0.6 = 240 MPa |
| 8.8 | 800 MPa | 0.8 | 800 × 0.8 = 640 MPa |
| 10.9 | 1,000 MPa | 0.9 | 1,000 × 0.9 = 900 MPa |
| 12.9 | 1,200 MPa | 0.9 | 1,200 × 0.9 = 1,080 MPa |
In practice, yield matters more than tensile strength. A tightened bolt works like a very stiff spring held within its elastic range. Push it past yield and it no longer springs back, so the clamp force it was meant to hold starts to disappear.
Grade, property class or product grade?
Site teams and purchase orders say “grade”, while ISO says “property class”. Both mean the same strength code. Product grade is something else. The letters A, B and C in standards such as IS 1363 and IS 1364 describe dimensional tolerance and finish, not strength. A “grade C bolt” is a black bolt made to looser tolerances, and it tells you nothing about strength until a property class is added.
Two other shortcuts cause confusion in Indian purchasing. “HT bolt” (high tensile) usually means 8.8 or 10.9, but it isn’t a grade, and a supplier can read it either way. A steel name such as EN8 or EN19 describes the raw material, not the guaranteed strength of the finished bolt. Always write the property class. Our comparison of MS, HDG, stainless and heat-treated fasteners shows how heat treatment fits alongside material and finish.
The Four Grades Side by Side
The table below gives the minimum values ISO 898-1 requires at room temperature. Class 8.8 has two columns because the requirement steps up slightly above M16.
| Property | 4.6 | 8.8 (≤ M16) | 8.8 (> M16) | 10.9 | 12.9 |
|---|---|---|---|---|---|
| Minimum tensile strength (MPa) | 400 | 800 | 830 | 1,040 | 1,220 |
| Minimum yield or 0.2% proof strength (MPa) | 240 | 640 | 660 | 940 | 1,100 |
| Proof stress, Sp (MPa) | 225 | 580 | 600 | 830 | 970 |
| Vickers hardness (HV) | 120–220 | 250–320 | 255–335 | 320–380 | 385–435 |
| Rockwell hardness | 67–95 HRB | 22–32 HRC | 23–34 HRC | 32–39 HRC | 39–44 HRC |
| Minimum elongation after fracture | 22% | 12% | 12% | 9% | 8% |
| Typical steel and treatment | Low or medium carbon steel, no quench and temper needed | Medium carbon, boron or alloy steel, quenched and tempered | As for ≤ M16 | Boron or alloy steel, quenched and tempered | Alloy steel (Cr, Mo, Ni or V), quenched and tempered |
Three rows deserve a closer look.
Proof stress is the figure inspectors test against. The bolt is loaded to its proof load, held and released, and it must return to its original length. Proof stress sits just below yield, at about 88–94% of it depending on the grade, so it marks the edge of the safe elastic range.
Hardness rises steadily with grade. A portable hardness reading well outside the range is a red flag that a bolt isn’t what its head claims, although it doesn’t replace a proper tensile test.
Elongation falls as strength rises. In a standard tensile test piece, 4.6 steel stretches by more than a fifth before it breaks, while 12.9 manages less than a tenth. That trade-off shapes where each grade belongs.
The label is a floor, not the exact figure
The label and the minimum don’t always match. A 10.9 bolt is “1,000 MPa” by name, but the standard requires at least 1,040 MPa. A 12.9 must reach 1,220 MPa, and an 8.8 above M16 must reach 830 MPa. That is why our specification for class 10.9 high-tensile hex bolts lists a tensile strength of 1,040 N/mm² minimum rather than 1,000. When you check a test certificate, compare it with the minimum, not with the number on the head.
What Each Grade Holds, in Kilonewtons
Stress figures become useful once you turn them into loads. To do that, multiply the stress by the bolt’s tensile stress area (As), which is the effective cross-section of the threaded part. Here are the results for the coarse-thread sizes buyers order most often.
| Size | As (mm²) | 4.6 | 8.8 | 10.9 | 12.9 |
|---|---|---|---|---|---|
| M12 | 84.3 | 19.0 | 48.9 | 70.0 | 81.8 |
| M16 | 157 | 35.3 | 91.0 | 130 | 152 |
| M20 | 245 | 55.1 | 147 | 203 | 238 |
| M24 | 353 | 79.4 | 212 | 293 | 342 |
| Size | 4.6 | 8.8 | 10.9 | 12.9 |
|---|---|---|---|---|
| M12 | 33.7 | 67.4 | 87.7 | 103 |
| M16 | 62.8 | 125 | 163 | 192 |
| M20 | 98.0 | 203 | 255 | 299 |
| M24 | 141 | 293 | 367 | 431 |
Take the M16 row as a worked example. An M16 class 8.8 bolt must hold 91 kN, about the weight of 9.3 tonnes, without stretching permanently. At 10.9 the proof load rises to 130 kN, an increase of roughly 43%. At 12.9 it reaches 152 kN, about two-thirds more than the 8.8. Going the other way, a 4.6 bolt of the same size proves at only 35.3 kN, under 40% of the 8.8 figure.
Two cautions apply. These are test values, not working loads: real designs apply safety factors and allow for preload, shear, prying and fatigue, so never size a joint from this table alone. And a bigger number only helps if the rest of the joint can match it, which is why each grade has its own natural territory.
Where Each Grade Belongs
Class 4.6: the general-purpose mild steel bolt
Class 4.6 is made from low or medium carbon steel without quenching and tempering. It is soft, ductile, forgiving and cheap. In Indian structural work it is the classic “black bolt”, made to product grade C under IS 1363 and used snug-tight in ordinary bearing-type connections.
Typical uses include secondary steelwork, purlins and cleats, fencing, light brackets, timber connections and many foundation bolts where the design calls for ductility rather than high strength. Plain mild steel bolt, nut and washer sets generally fall in this territory, as do many carriage bolts. Our comparison of hex bolts and carriage bolts shows where each head style fits.
What 4.6 can’t do well is hold a high preload. Its yield strength is low, so it isn’t suited to slip-critical, fatigue-loaded or vibrating joints that depend on clamp force.
Class 8.8: the workhorse
If Indian industry has a default high-strength bolt, it is 8.8. Quenching and tempering roughly doubles its strength compared with 4.6, while it keeps a useful 12% elongation. It handles general machinery, equipment bases, structural connections, pipe supports and most bolted plant. HSFG bolts to IS 3757 are also made in this class, marked 8.8S.
Class 8.8 is also the easiest high-strength grade to galvanise, and hot-dip galvanised 8.8 assemblies are standard for outdoor steelwork. See our HDG bolt, nut and washer range.
Class 10.9: high strength for heavy, preloaded joints
Class 10.9 uses boron or alloy steel, heat-treated to a higher hardness. It suits joints where the clamp force itself carries the load: slip-critical structural connections (HSFG class 10.9S), crane and earthmoving equipment, presses, heavy machinery, wind towers and large rotating equipment. Because each bolt can hold more preload, a design can often use a smaller 10.9 bolt in place of a larger 8.8, or use fewer bolts.
It asks more of the rest of the joint: a class 10 nut, hardened washers, controlled tightening and careful coating choices. Our HSFG fasteners and the structural engineer’s guide to HSFG bolting cover the slip-critical side in detail.
Class 12.9: maximum strength in a compact package
Class 12.9 is an alloy steel grade, typically chromium-molybdenum steel, found mostly on socket head cap screws. It lets designers carry high loads through small diameters and heads, which is why it appears in press tools, dies, moulds, machine-tool fixtures, gearboxes and compact machinery. CSK and Allen bolts are commonly supplied in 10.9 or 12.9.
It is also the least forgiving grade. Elongation drops to 8%, hardness climbs above 385 HV and the risk of hydrogen embrittlement rises sharply. Keep 12.9 for dry, controlled environments where the design calls for it, not as a general upgrade.
What about 4.8, 5.6, 5.8, 6.8 and 9.8?
These in-between classes exist but are less common in Indian bulk trade. Classes 4.8, 5.8 and 6.8 are usually cold-worked steels with a higher yield ratio and less ductility than 4.6, often seen on small screws. Class 5.6 is a slightly stronger relative of 4.6, and class 9.8 applies only up to M16, sitting between 8.8 and 10.9.
Reading the Head: How to Identify a Bolt’s Grade
ISO 898-1 requires hexagon-head bolts and screws of 5 mm diameter and above to carry two marks wherever the shape allows: the property class and the manufacturer’s identification mark. Socket head cap screws of class 8.8 and above must be marked the same way. The marks are embossed or indented, usually on top of the head.
A few details help on site:
- The dot can be left out. “88” or “109” on a head means 8.8 or 10.9.
- A leading zero means reduced capacity. A mark such as “08.8” tells you the part’s shape, for example a low head, prevents it from carrying the full load of its class.
- Nuts are marked too. Hexagon nuts of 5 mm and above carry their class number, such as 8 or 10, or an equivalent clock-face code.
- Radial lines belong to the inch system. Three lines on a head mean SAE Grade 5 and six lines mean SAE Grade 8. They are not metric classes.
- An unmarked bolt is an unknown bolt. Don’t assume it is 4.6, and keep it out of structural and safety-critical joints.
Markings can be faked or misapplied, so for critical work, buy against a test certificate and keep the lot number with the job. Our article on fastener packaging and lot traceability explains why.
Nuts and Washers Must Keep Up with the Bolt
A bolt is only as strong as the threads it pulls against. Nut property classes come from ISO 898-2, adopted in India as IS 1367 (Part 6). The rule of thumb: the nut’s class number should be at least the first number of the bolt’s class, and a nut of a higher class is always acceptable.
| Bolt grade | Minimum nut class | Washer | Watch out for |
|---|---|---|---|
| 4.6 | 5 | Plain mild steel washer | Over-tightening a soft bolt |
| 8.8 | 8 | 200 HV plain washer | Class 5 or unmarked nuts mixed into the same bin |
| 10.9 | 10 | 300 HV hardened washer | Soft washers that embed and shed preload |
| 12.9 | 12 | Hardened washer, or a hard seating face | Electroplated parts without hydrogen controls |
Why does it matter? Pair a high-strength bolt with a weak nut and the nut threads strip before the bolt reaches its rated load, often without any visible sign until the joint is loaded. A properly matched nut keeps the weak point in the bolt shank, where the designer expects it.
Washers matter for a related reason. Under a 10.9 bolt, the bearing pressure can exceed what a soft washer can carry, so it yields and embeds and clamp force leaks away. ISO 7089 plain washers come in two hardness classes: 200 HV for bolts up to 8.8 and 300 HV for bolts up to 10.9. Our plain washers include heat-treated (HT) versions for this job, and HSFG assemblies use hardened washers to IS 6649.
The same logic applies to threaded rod: high-tensile studs should be joined with a high-tensile long nut, not a mild steel one.
Higher Isn’t Automatically Better
Fitting a stronger bolt feels like a safe upgrade. Often it isn’t, for four reasons.
- Less ductility means less warning. An overloaded 4.6 or 8.8 bolt usually stretches and necks before it breaks. A 12.9 bolt gives far less warning.
- Fatigue strength barely improves. VDI 2230, the German guideline for bolted joint design, gives threads rolled before heat treatment an endurance limit that depends on diameter, not on property class. A higher grade helps in fatigue mainly because it can hold more preload, which keeps the alternating load on the bolt small. Under the same alternating load, it gains little.
- Hydrogen embrittlement risk climbs with hardness. Hydrogen from acid cleaning, electroplating or corrosion in service can cause sudden brittle fracture under load, sometimes hours or days after assembly. ISO 4042 tightens its controls above 360 HV and again above 390 HV, and the hard end of 10.9 and all of 12.9 sit above the first threshold.
- Some bolts are meant to be the weak link. Shear bolts on couplings, crushers and farm implements are deliberately soft so they fail before a gearbox or shaft does. Upgrading them moves the failure to a far more expensive part.
There are knock-on effects too. A higher grade needs a different tightening torque, as our torque specifications guide explains, along with a stronger nut and a harder washer. If the bolt threads into a tapped hole in cast iron or aluminium, a stronger bolt may simply strip the hole sooner. Substitute only with the designer’s approval.
Coatings: What Each Grade Can Safely Wear
Coating choice and grade are linked. The harder the bolt, the more care the coating process needs.
| Coating | 4.6 | 8.8 | 10.9 | 12.9 |
|---|---|---|---|---|
| Plain, oiled or black oxide | Suitable | Suitable | Suitable | Suitable |
| Electroplated zinc (ISO 4042) | Suitable | Suitable | Controlled process with baking | High risk; avoid unless strictly controlled |
| Hot-dip galvanised (ISO 10684) | Suitable | Suitable | Permitted with controlled cleaning and certification | Outside the standard; don’t specify |
| Zinc flake (ISO 10683) | Suitable | Suitable | Preferred option | Preferred option |
Some notes on the table:
- Hot-dip galvanising. ISO 10684 covers bolts up to class 10.9 and nuts up to class 12. For parts with a hardness of 320 HV or more, it calls for inhibited acid or mechanical cleaning to limit hydrogen pick-up. Class 12.9 falls outside the standard.
- Electroplating. ISO 4042 sets its hydrogen embrittlement controls by hardness band. Baking after plating reduces the risk but can’t guarantee it is gone, which is why many engineers avoid electroplating 12.9 altogether.
- Zinc flake. These coatings are applied without electrolysis, so the coating process itself doesn’t introduce hydrogen. They are the usual choice when 10.9 or 12.9 bolts need corrosion protection.
To match a finish to the site environment, see our guide to preventing fastener corrosion in coastal and industrial environments. Our explainer on MS vs GI covers how galvanising itself works.
Other Grading Systems You’ll Meet
Stainless steel bolts
Stainless bolts don’t use the X.Y system. ISO 3506-1 grades them by steel group and strength: A2-70 is 304-type austenitic stainless with a minimum tensile strength of 700 MPa, and A4-80 is 316-type at 800 MPa. Their 0.2% proof strength is also lower than that of a carbon steel bolt with similar tensile strength: A2-70 reaches 450 MPa against 640 MPa for 8.8, and A4-80 reaches 600 MPa. So A2-70 is not a like-for-like swap for 8.8. Choose stainless steel bolts for corrosion resistance, then check the strength separately.
SAE and ASTM inch-series grades
Imported equipment and American specifications use inch-series grades. The equivalents below are approximate, and because the threads differ, the parts are never interchangeable.
| Metric class | Nearest inch-series grade | Inch grade minimum tensile |
|---|---|---|
| 4.6 | ASTM A307 Grade A | 60 ksi (≈ 414 MPa) |
| 8.8 | SAE J429 Grade 5 / ASTM F3125 Grade A325 | 120 ksi (≈ 827 MPa) up to 1 inch |
| 10.9 | SAE J429 Grade 8 / ASTM F3125 Grade A490 | 150 ksi (≈ 1,034 MPa) |
| 12.9 | ASTM A574 socket head cap screws | 170–180 ksi (≈ 1,172–1,241 MPa) |
Watch the trap in the names: SAE Grade 8 is not class 8.8. Grade 8 is much closer to 10.9. Our buyer’s reference to fastener standards covers the wider equivalence picture.
Where the grades sit in Indian standards
| Standard | What it covers |
|---|---|
| IS 1367 (Part 3):2017 | Mechanical properties of bolts, screws and studs; identical to ISO 898-1:2013 |
| IS 1367 (Part 6):2025 | Mechanical properties of nuts; identical to ISO 898-2:2022 |
| IS 1363 | Hexagon bolts, screws and nuts of product grade C (black bolts, usually 4.6) |
| IS 1364 | Hexagon bolts, screws and nuts of product grades A and B |
| IS 3757, IS 6623, IS 6649 | HSFG bolts (8.8S, 10.9S), their nuts (8S, 10S) and hardened washers |
Choosing the Grade: Five Questions
Grade is one decision among several, and our guide on how to choose the right industrial fasteners covers the full selection process. For the grade itself, these five questions settle most cases.
- What does the drawing or design specify? If a grade is stated, supply exactly that. Upgrading or downgrading is a design change.
- Does the joint rely on clamp force? Snug-tight bearing joints often work well with 4.6 or 8.8. Slip-critical, fatigue-loaded or vibrating joints need preload, which points to 8.8 or 10.9.
- What environment and coating? Outdoor and galvanised steelwork usually means 8.8, or 10.9 with a certified process. Wet or corrosive service is a poor home for 12.9.
- What does the bolt thread into? The nut must match the grade, and a tapped hole in a softer metal limits the useful grade. Thread pitch plays a part here too, as our comparison of coarse thread vs fine thread explains.
- Can the site achieve and verify the preload? High grades only pay off when they are tightened properly. DTI washers are one way to confirm tension on structural joints.
How to Write the Grade on a Purchase Order
“HT bolt M16 × 80” leaves the grade to the supplier’s judgement. A complete line names the standard, size, class, finish and mating parts:
- Hex bolt ISO 4014, M16 × 80, property class 8.8, hot-dip galvanised to ISO 10684, with class 8 nut and plain washer supplied as matched sets, test certificate required: 500 sets.
- Socket head cap screw ISO 4762, M10 × 40, property class 12.9, plain oiled finish, no electroplating: 1,000 nos.
Our fastener RFQ guide has a complete template, and our article on reading a fastener specification sheet shows how to check the quote and certificates that come back.
Frequently Asked Questions
What does 8.8 mean on a bolt?
It is the bolt’s property class under ISO 898-1, adopted in India as IS 1367 (Part 3). The first 8 means a nominal tensile strength of 8 × 100 = 800 MPa. The second 8 means the yield strength is 80% of that, about 640 MPa. Above M16, the standard requires at least 830 MPa tensile and 660 MPa yield.
Which is stronger, 10.9 or 12.9?
Class 12.9 is stronger. It needs at least 1,220 MPa tensile against 1,040 MPa for 10.9, and it has about 17% more proof load at the same size. It is also harder, less ductile and more sensitive to hydrogen embrittlement, so 10.9 is often the better choice for outdoor, coated or shock-loaded joints.
Can I replace an 8.8 bolt with a 10.9 or 12.9 bolt?
Only with the designer’s approval. A higher grade needs a matching nut and hardened washer, a different tightening torque and a suitable coating. It can also move the failure point to a nut, a tapped hole or a more expensive component. A like-for-like replacement is the safe default.
Is grade 8.8 the same as SAE Grade 8?
No. Metric class 8.8 is roughly equivalent to SAE Grade 5, at about 120 ksi tensile. SAE Grade 8, at 150 ksi, is closer to metric class 10.9. The thread forms also differ, so metric and inch-series parts are never interchangeable.
What nut should I use with a 10.9 bolt?
Use a nut of property class 10 or higher to ISO 898-2, with a hardened washer of at least 300 HV under the part being turned. For HSFG work in India, use IS 6623 class 10S nuts and IS 6649 hardened washers with IS 3757 class 10.9S bolts.
Can 10.9 and 12.9 bolts be hot-dip galvanised?
Class 10.9 can be galvanised under ISO 10684, provided the galvaniser controls cleaning to limit hydrogen pick-up and can certify the process. Class 12.9 falls outside ISO 10684 and should not be hot-dip galvanised. Zinc flake coatings are the usual alternative for 12.9.
What grade is a black bolt or an unmarked bolt?
Black bolts in Indian structural work are usually product grade C bolts to IS 1363 in property class 4.6. An unmarked bolt has no verifiable grade at all. Treat it as unknown and keep it out of structural or safety-critical joints.
Conclusion
Every bolt grade is a promise about two stresses: the one at which the bolt breaks and the one at which it stops springing back. Class 4.6 promises ductility at low cost. Class 8.8 is the balanced default for most industrial and structural work. Class 10.9 carries heavy, preloaded joints, provided the nuts, washers, coating and tightening keep up. Class 12.9 is a specialist grade for compact, dry and well-controlled machinery.
So the right grade is the one the whole joint can use. If you have a drawing, a bolt schedule or even a sample from a failed joint, share it with our team through the contact page. We’ll quote the grade, nut, washer and finish as one matched set.
One thought on “Bolt Grades Explained: What Do 4.6, 8.8, 10.9 and 12.9 Mean?”